manualshive.com logo in svg

Hydronix Hydro-Control VI, Руководство по установке

Поделиться
Скачать
Hydronix Hydro-Control VI Скачать руководство пользователя страница 20

Mechanical Installation 

Chapter 2 

20 

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0 

6  Touch screen protective layer 

The touch screen has a thin sheet of plastic which protects it.  The sheet is not glued in place, but 

held around the edged by the bezel on the front of the Hydro-Control.  If the protector gets worn or 

dirty it can be replaced with Hydronix Part Number 0179. 

The touch screen protective layer can be removed by carefully applying pressure to the front of the 

Hydro-Control and sliding the sheet down slightly.  This will expose the corners of the sheet which 

can then be lifted away from the touch screen.  A blunt plastic tool can also be used to help lift the 

sheet if needed. 

To fit a new sheet, remove the sheet from the packaging taking care to keep the sheet clean and 

dust free.  Remove the protective covering from the rear (shiny) surface of the touch screen 

protector and then carefully fit the new protector over the screen so that the anti-glare (dull) front 

surface faces away from the touch screen. 

 

 

Содержание Hydro-Control VI









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды