Hydronix Hydro-Control VI Скачать руководство пользователя страница 37

Страница: 37 / 104

Chapter 4

Commissioning

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0

Fine Valve On Time

Seconds

0.5

0 – 100 s

Fine Valve Off Time

Seconds

0.5

0 – 100 s

Use Fine Valve Only

None

Yes/No

Averaging Time

Seconds

0 – 100 s

Cycle Loops

None

1 – 100

Resolution

Kg/lb

0-200

Water Mode

controls how the water is measured into the mixer. If using a water meter to

measure the water dosed into the mixer, this should be set to ‘Metered’. If using a weight

measurement system then ‘Weighed’ water mode should be selected. ‘Timed’ water mode is

recommended for use when there are problems with the water measurement device. More

information on selecting water modes is available in Chapter 5.

Pulses Per Litre

sets the number of pulses that are received when dosing one litre of water

into the mixer in Metered Mode.

Water Meter Timeout

is the amount of time after opening the water valve that the system will

wait before alarming if it has not received a water meter pulse.

Fine Delivery

is the quantity of water at the end of the preset or calculated dose that is fed

using the fine valve only.

Fine Valve Inflight

is the quantity of water that continues to flow after the fine valve has been

closed.

Coarse Valve Inflight

is the quantity of water that continues to flow after the coarse valve has

been closed. This valve is used when the Pre-wet phase is run in preset mode.

Fine Valve On Time

is the amount of time it takes to turn on the fine valve. This should be

referenced from the valve manufacturer’s data sheet.

Fine Valve Off Time

is the amount of time it takes to turn off the fine valve. This should be

referenced from the valve manufacturer’s data sheet.

The valve on/off times are used to set the minimum pulse of the valve during AUTO Mode

addition, to prevent the valves from being damaged due to excessive use.

Use Fine Valve Only

sets the system to only dose water using the fine valve. In this mode it

will never activate the coarse valve.

Averaging Time

is the amount of time at the end of the dry and wet mix phases that the system

will use for taking an average value of the moisture reading.

Cycle Loops

is a setting that is used to repeat the wet mix addition and the wet mixing phases.

It is generally only useful for linearity testing, and so should be left set to 1.

Resolution

sets the resolution of the weigh scale value for systems set to use weighed water.

This value is not displayed unless the water mode is set to weighed water.

Содержание Hydro-Control VI









































































































Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды

Hydronix Hydro-Control VI, Руководство по установке

Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды