Hydronix Hydro-Control VI Скачать руководство пользователя страница 14

Страница: 14 / 104

Introduction

Chapter 1

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0

2 About this manual

This manual is not a user guide. It is designed as a reference guide for engineers who are

designing, installing or commissioning a Hydro-Control VI system.

This manual complements the Operators Guide which details how to setup and calibrate recipes

in the Hydro-Control VI. In order to understand the choices of operation and consequent design

requirements it is advisable to read the Operators Guide before reading this manual.

The manual is divided into 3 sections covering the mechanical installation, the electrical installation

and the commissioning of the unit.

3 Safety

The Hydro-Control VI has been designed to meet the requirements of IEC/EN 61010-1 : 2001 and

ANSI/UL 61010-1 Second Edition.

This equipment is designed to be safe under the following conditions.

3.1

Precautions

This unit is suitable for indoor use only.

If the equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

The final installation should have a means to disconnect the electrical supply to

the unit. It should be marked as the disconnecting device and be within easy reach of the

operator.

Disconnect all signals from any voltage supply before the unit is opened for any adjustment,

maintenance or repair work.

Ensure that only fuses of the correct type and rating are fitted.

Ensure that the Hydro-Control is mounted in an environment that will not cause electrical

interference.

3.2

Explanation of Symbols and Markings

It is important to understand the meaning of the various symbols and markings on the Hydro-

Control equipment as follows:

Figure 2: The base of the Hydro-Control VI with the label for the Earth stud in the red circle

Содержание Hydro-Control VI









































































































Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды

Hydronix Hydro-Control VI, Руководство по установке

Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды