Husqvarna TE 250 Скачать руководство пользователя

Страница: 133 / 169

SERVICE WORK ON THE ENGINE 18

131

S05315-10

–

Plug in wake-up connector

for priming the oil pump to the

diagnostics connector

The combination instrument lighting is activated.

Info

The connector is included as part of the motorcycle's

separate enclosure.

–

Wait for at least five seconds.

–

Release the fixing means from the throttle grip.

The oil pump is timed.

Info

The oil pump is actuated at various speeds.
The procedure is clearly audible.

–

Wait until you can no longer hear the oil pump operating.

–

Disconnect the wake-up connector from the diagnostics con-

nector.

F02321-10

–

Check whether air bubbles are visible in the hose

» If air bubbles are visible:

–

Repeat the entire procedure until air bubbles are no

longer visible.

–

Mount protection cap on the diagnostics connector.

–

Mount the EFI control unit on the rubber lugs.

Finishing work

–

Mount the seat. (

p. 67)

–

Install the air filter box cover. (

p. 68)

18.4

Cleaning the oil screen in the oil tank

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Preparatory work

–

Remove the main silencer. (

p. 70)

–

Remove the air filter box cover. (

p. 68)

–

Remove the seat. (

p. 67)

–

Remove the right side cover. (

p. 72)

–

Remove the fuel tank.

(

p. 73)

–

Raise the motorcycle with a lift stand. (

p. 55)

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды