Husqvarna TE 250 Скачать руководство пользователя

Страница: 164 / 169

29 LIST OF SYMBOLS

162

29.1

Red symbols

Red symbols indicate an error condition that requires immediate intervention.

The oil level warning lamp lights up red

–

Oil level has reached the

MIN

marking. Ride for no

more than until the remaining fuel in the tank is depleted and at the next opportunity refuel

with 2-stroke oil.

29.2

Yellow and orange symbols

Yellow and orange symbols indicate an error condition that requires prompt intervention. Active driving aids are

also represented by yellow or orange symbols.

Malfunction indicator lamp lights up/flashes yellow

–

The OBD has detected a malfunction in

the vehicle electronics. Come safely to a halt, and contact an authorized Husqvarna Motor-

cycles workshop.
The fuel level warning lamp lights up yellow

–

The fuel level has reached the reserve mark.

29.3

Green and blue symbols

Green and blue symbols reflect information.

Turn signal indicator lamp flashes green

–

The turn signal is switched on.

The high beam indicator lamp lights up blue

–

The high beam is switched on.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды