Husqvarna TE 250 страница 84 Скачать руководство пользователя

Страница: 84 / 169

12 SERVICE WORK ON THE CHASSIS

H03712-10

Main work

–

Check the throttle cable routing.

Both throttle cables must be routed, side by side, on the

back of the handlebars, above the fuel tank bracket on the

right of the frame to the throttle valve body. Both throttle

cables must be secured behind the rubber strap of the fuel

tank support.

» If the throttle cable is not routed as specified:

–

Correct the throttle cable routing.

Finishing work

–

Install the fuel tank.

(

p. 74)

–

Install the right side cover. (

p. 72)

–

Mount the seat. (

p. 67)

–

Install the air filter box cover. (

p. 68)

12.40

Checking the rubber grip

401197-01

–

Check the rubber grips on the handlebar for damage, wear,

and looseness.

Info

The rubber grips are vulcanized onto a sleeve on the

left and onto the handle tube of the throttle grip on the

right. The left sleeve is clamped onto the handlebar.
The rubber grip can only be replaced with the sleeve

or the throttle tube.

» If a rubber grip is damaged or worn:

–

Change the rubber grip.

S04838-10

–

Check that screw

is firmly seated.

Guideline

Screw, fixed

grip

5 Nm (3.7 lbf ft)

Loctite

243™

Diamond

must be positioned visibly as shown in the

figure.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды