Husqvarna TE 250 страница 56 Скачать руководство пользователя

Страница: 56 / 169

11 TUNING THE CHASSIS

11.16

Adjusting the handlebar position

Warning

Danger of accidents

A repaired handlebar poses a safety risk.

If the handlebar is bent or straightened, the material becomes fatigued. The handlebar may break as a

result.

–

Change the handlebar if the handlebar is damaged or bent.

B00375-10

–

Remove screws

. Take off the handlebar clamps. Remove

the handlebar and lay it to one side.

Info

Cover the components to protect them against dam-

age.
Do not kink the cables and lines.

–

Remove screws

. Take off the handlebar supports.

–

Place the handlebar supports in the required position. Mount
and tighten screws

Guideline

Screw, handle-

bar support

M10

40 Nm (29.5 lbf ft)

Loctite

243™

Info

Position the left and right handlebar supports evenly.

–

Position the handlebar.

Info

Make sure the cables and wiring are positioned cor-

rectly.

–

Position the handlebar clamps. Mount screws

and tighten

evenly.
Guideline

Screw, handlebar

clamp

20 Nm (14.8 lbf ft)

Info

Make sure the gap widths are even.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды