Husqvarna TE 250 Скачать руководство пользователя

Страница: 94 / 169

13 BRAKE SYSTEM

13.8

Adjusting the basic position of the foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear

brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

H03722-10

–

Detach spring

–

Loosen nut

and, with push rod

, turn it back until you

have maximum free travel.

–

To adjust the basic position of the foot brake lever to individ-
ual requirements, loosen nut

and turn screw

accord-

ingly.

Info

The range of adjustment is limited.

–

Turn push rod

accordingly until you have free travel

. If

necessary, adjust the basic position of the foot brake lever.
Guideline

Free travel of foot brake

lever

3 … 5 mm (0.12 … 0.2 in)

–

Hold screw

and tighten nut

Guideline

Nut, foot brake lever

stop

20 Nm (14.8 lbf ft)

–

Hold push rod

and tighten nut

Guideline

Remaining nuts,

chassis

10 Nm (7.4 lbf ft)

–

Attach spring

13.9

Checking the rear brake fluid level

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the specified marking or the specified value, the brake system is

leaking or the brake linings are worn down.

–

Check the brake system and do not continue riding until the problem is eliminated. (Your authorized

Husqvarna Motorcycles workshop will be glad to help.)

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service

schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды