Husqvarna TE 250 страница 37 Скачать руководство пользователя

Страница: 37 / 169

PREPARING FOR USE 8

8.7

Preparing the vehicle for rides on wet and muddy circuits

M01106-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Observe the fitting instructions for Husqvarna Motor-

cycles technical accessories.

600868-01

–

Mount the steel sprocket.

–

Clean the motorcycle. (

p. 137)

–

Straighten the bent radiator fins carefully.

8.8

Preparing vehicle for high temperatures or slow riding

V00899-01

–

Check the radiator cap.

Value on the radiator cap

1.8 bar (26 psi)

» If the indicated value does not correspond to the setpoint

value:

Warning

Danger of scalding

During motorcycle

operation, the coolant gets very hot and is

under pressure.

–

Do not open the radiator, the radiator

hoses or other cooling system compo-

nents if the engine or the cooling system

are at operating temperature.

–

Allow the cooling system and the engine

to cool down before you open the radiator,

the radiator hoses or other components of

the cooling system.

–

In the event of scalding, rinse the area

affected immediately with lukewarm water.

–

Change the radiator cap.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды