Husqvarna TE 250 страница 40 Скачать руководство пользователя

Страница: 40 / 169

9 RIDING INSTRUCTIONS

401944-10

–

Take the motorcycle off side stand

and secure the side

stand with rubber strap

–

Shift the transmission into neutral.

(All EU/AR/CN standard models)

–

Turn the emergency OFF switch to the position .

Condition

Ambient temperature: < 10 °C (< 50 °F)

–

Pull the cold start button out all the way and turn it by a ¼

turn.

Info

If the engine is warm, the cold start button must

be deactivated.

400733-01

–

Press the start button.

Info

Do not open the throttle.
Press the start button for a maximum of 5 seconds.

Wait for 30 seconds before a further attempt at start-

ing.
At temperatures below 15 °C (60 °F), several attempts

at starting may be necessary to warm-up the lithium-

ion battery and thereby increase the starting power.
During the starting process, the malfunction indicator

lamp lights up.

9.3

Starting off

Info

Switch on the light before riding the vehicle. You will be seen earlier by other motorists.
When you are riding, the side stand must be folded up and secured with the rubber strap.

–

Pull the clutch lever, shift into first gear, release the clutch lever slowly and at the same time open the throt-

tle carefully.

9.4

Shifting, riding

Warning

Danger of accidents

If you change down at high engine speed, the rear wheel blocks and the engine

races.

–

Do not change into a low gear at high engine speed.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды