Husqvarna TE 250 Скачать руководство пользователя

Страница: 69 / 169

SERVICE WORK ON THE CHASSIS 12

S04827-11

–

Attach the frame protector in area

and position it.

–

Mount and tighten screws

with the washers.

Guideline

Screw, frame pro-

tector

3 Nm (2.2 lbf ft)

–

Mount the new cable ties.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 55)

12.18

Removing the seat

Preparatory work

–

Remove the air filter box cover. (

p. 68)

F02310-10

Main work

–

Remove screw

H02218-10

–

Raise the rear of the seat, pull the seat back, and lift it off.

12.19

Mounting the seat

H02218-11

Main work

–

Mount the front of the seat on the collar bushing of the fuel

tank and the rear in the bracket.

–

Push the seat forward.

–

Make sure the seat is latched in place correctly.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды