Husqvarna TE 250 Скачать руководство пользователя

Страница: 131 / 169

SERVICE WORK ON THE ENGINE 18

129

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and

death.

–

Always make sure there is sufficient ventilation

when running the engine.

–

Use effective exhaust extraction when starting or

running the engine in an enclosed space.

–

Start the engine and check the response.

18.2

Checking 2-stroke oil level

Warning

Engine failure

The engine will not be lubricated unless there is 2-stroke oil in the oil tank.

If the oil level warning light lights up, the 2-stroke oil is sufficient for the remaining tank of fuel.

–

As soon as the oil level warning light lights up, ride for no longer than until the remaining fuel in the

tank is depleted.

–

At the next opportunity add 2-stroke oil before you refuel.

–

Time the oil pump if the 2-stroke oil hose has been removed or the 2-stroke oil tank has been fully

depleted in error.

Preparatory work

–

Stand the motorcycle upright on a horizontal surface.

F02318-10

Main work

–

Check the 2-stroke oil level in the oil tank.

Info

For one tank of fuel, the 2-stroke oil tank must be filled
up to at least the upper edge

The 2-stroke oil tank must be completely filled if possible.

» If the 2-stroke oil level is too low:

–

Add 2-stroke oil. (

p. 42)

18.3

Priming oil pump

Warning

Engine failure

The engine will not be lubricated unless there is 2-stroke oil in the oil tank.

If the oil level warning light lights up, the 2-stroke oil is sufficient for the remaining tank of fuel.

–

As soon as the oil level warning light lights up, ride for no longer than until the remaining fuel in the

tank is depleted.

–

At the next opportunity add 2-stroke oil before you refuel.

–

Time the oil pump if the 2-stroke oil hose has been removed or the 2-stroke oil tank has been fully

depleted in error.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды