Husqvarna TE 250 Скачать руководство пользователя

Страница: 96 / 169

13 BRAKE SYSTEM

S04468-10

Main work

–

Stand the vehicle upright.

–

Remove the cable ties on the frame protector.

–

Remove screw cap

with membrane

and the shim.

–

Add brake fluid up to the marking

Brake fluid DOT 4 / DOT 5.1 (

p. 155)

–

Mount and tighten screw cap with the membrane and the

shim.

Info

Clean up overflowed or spilled brake fluid immediately

with water.

–

Mount new cable ties on the frame protector.

13.11

Checking the brake linings of the rear brake

Warning

Danger of accidents

Worn-out brake linings reduce the braking effect.

–

Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcy-

cles workshop will be glad to help.)

S04469-10

–

Check the brake linings for minimum thickness

Minimum thickness

≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the rear brake linings.

(

p. 94)

–

Check the brake linings for damage and cracking.
» If damage or wear is encountered:

–

Change the rear brake linings.

(

p. 94)

13.12

Changing the rear brake linings

Warning

Danger of accidents

Incorrect servicing will cause the brake system to fail.

–

Ensure that service work and repairs are performed professionally. (Your authorized Husqvarna

Motorcycles workshop will be glad to help.)

Warning

Skin irritation

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact

with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды