Husqvarna TE 250 страница 75 Скачать руководство пользователя

Страница: 75 / 169

SERVICE WORK ON THE CHASSIS 12

12.30

Removing the fuel tank

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not fuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

–

Keep fuels correctly in a suitable canister, and out of the reach of children.

Preparatory work

–

Remove the air filter box cover. (

p. 68)

–

Remove the seat. (

p. 67)

–

Remove the right side cover. (

p. 72)

H03702-10

Main work

–

Unplug connector

of the fuel pump.

–

Clean quick release coupling

thoroughly with

compressed air.

Info

Under no circumstances should dirt enter into the fuel

line. Dirt in the fuel line clogs the injection valve!

H03703-10

–

Disconnect the quick release coupling.

Info

Remaining fuel may flow out of the fuel hose.

–

Mount wash cap set

Wash cap set (81212016100)

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды