Huawei FusionCol8000-E24 Скачать руководство пользователя страница 27

Страница: 27 / 269

Name

Description

Air filter

● Indoor return air filter: G4 filters
● Outdoor intake air filter: G3 filters

Precooling

module

● Wet film spraying for evaporative cooling lowers water

quality requirements and improves environmental

adaptability. The structure is simple and easy to

disassemble, clean, and maintain.

● Spray water is in direct contact with the precooling

module. The precooling module is periodically maintained

to prevent the core from scaling and corrosion.

Heat

exchanger

core

● An efficient heat exchanger core is used. The heat

exchanger core adopts the innovative flow design, which

improves efficiency and reduces air resistance.

● The heat exchanger core has high adaptability. It applies

to high-temperature, low-temperature, and high- and low-

temperature impact environments.

Condenser The condenser adopts the flow design with a low wind

resistance.

Exhaust

fan

● A Huawei-developed high-speed fan is used, which

features large air volume, high static pressure, high

reliability, and a long service life.

● The fan is separated from the drive. The fan efficiency is

improved by more than 8% compared with a common EC

fan.

● The direct drive that the fan adopts has higher

transmission efficiency than the belt drive, which reduces

belt replacement and routine checks.

Evaporator The synergy field principle and computational fluid dynamics

(CFD) are used to optimize the flow path design, greatly

improving the heat exchange efficiency. The evaporator air

flow organization is more reasonable, and the air resistance

is smaller.

Spray

pump

● A horizontal three-stage centrifugal pump is used, which

features high pump lift, small size, high reliability, and

long service life.

● The water pump is made of new lubrication sealing

material. Wear parts such as water pump spindle seal and

seal ring do not need to be maintained in the life cycle.

● The variable-frequency drive power supply mode is used

to implement soft startup of the water pump, improving

the pump reliability.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

2 Product Description

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды