Huawei FusionCol8000-E24 Скачать руководство пользователя страница 19

Страница: 19 / 269

●

When moving the equipment by hand, wear protective gloves to prevent

injuries.

●

Move or lift the equipment by holding its handles or lower edges. Do not hold

the handles of modules (such as power supply units, fans, and boards) that

are installed in the equipment because they cannot support the weight of the

equipment.

●

Avoid scratching the cabinet surface or damaging cabinet components and

cables during equipment transportation.

●

When transporting the equipment using a forklift truck, ensure that the forks

are properly positioned so that the equipment does not topple. Before moving

the equipment, secure it to the forklift truck using ropes. When moving the

equipment, assign dedicated personnel to take care of it.

●

Choose a road with good conditions or sea for transportation to ensure

equipment safety. Avoid tilt or jolt during transportation.

●

Move the cabinet with caution. Any bumping or falling may damage the

equipment.

1.6 Cooling System Safety

Welding

●

At least two persons are required on a welding site.

●

A welder must have a work permit.

●

A welding site must be free from inflammables.

●

Ensure that a fire extinguisher, wet wiper, and water container are available.

●

A burning welding torch must not be placed on a component or on the floor,

and must not be placed in a metal container with acetylene and oxygen.

Otherwise, the gas may leak and cause a fire.

●

High-temperature pipes after welding must be promptly cooled.

●

Do not weld or cut on pressurized containers or pipes. Electric devices must be

powered off before welding.

High Temperature and Pressure

●

When maintaining or replacing components, pay attention to high-

temperature components (such as the compressor, refrigerant pipe, and

electric heater) to prevent scalds.

●

When maintaining or replacing components, pay attention to high-pressure

components (such as the compressor and refrigerant pipe) to prevent the

refrigerant system from being cracked or exploded due to misoperations.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

1 Safety Information

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды