Huawei FusionCol8000-E24 Скачать руководство пользователя страница 96

Страница: 96 / 269

Networking

CAN Teamwork

RS485 Monitoring

Description

One teamwork network

supports a maximum of 32

units. On the Teamwork

Settings screen of the display

modules of the first and last

units, set Enable teamwork

CAN resistor to Yes.

It takes 3 x

seconds to

collect data from

units. If

the time required for the host

to collect data from all units

does not meet the

performance requirements,

group the units.
● If units are not grouped (

= 1), set RS485 monitoring

grouping to Enable on the

Modbus Settings screen

for each unit.

● If units are grouped (

> 1;

recommended:

≤ 4), set

RS485 monitoring

grouping to Enable on the

Modbus Settings screen

for the unit with the

COM/FE port connected.

Retain the default setting

(Disable) for other units.

NO TE

● Connect the COM/FE port on the main control module of the last unit in each group to

the RS485 port on the host.

● Customers can purchase an ECC and NetEco as the monitoring system.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

5 System Installation (FDC Scenario)

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды