Huawei FusionCol8000-E24 Скачать руководство пользователя страница 234

Страница: 234 / 269

Repainting the Unit

Prerequisites

●

Communicate with the customer before paint repair: The front, rear, left, and

right surfaces of the unit are grade A surfaces, and the bottom and top

surfaces are grade B surfaces.
–

The color may be slightly different when grade A surfaces are repainted.

Reach an agreement with the customer before repainting.

–

Acceptance criteria for repainting of grade B surfaces: The repainted area

should have the same color as surrounding areas. The color difference ΔE

is not greater than 3. (Use a colorimeter to measure the color difference.

If a colorimeter is not available, check that no obvious boundary exists

between the repainted area and its surrounding.) The paint should also

be free from bulges, scratches, flake-off, or cracks.

●

Ensure that the outdoor area without shelters is not subject to bad weather

conditions such as raining, sandstorm, strong wind, or snowing during paint

repair.

●

Ensure that the required paint has been prepared based on the color palette

delivered with the product. The color palette is used only for the cabinet, and

the color code is RAL9003.

Context

The exterior of the unit should be intact. If the surface is bumped, scratched, or

rusted, the paint should be repaired.

NO TE

Check the paint damage on the unit and prepare appropriate tools and materials. The

number of materials depends on site requirements.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

B Repainting the Unit

225

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды