Huawei FusionCol8000-E24 Скачать руководство пользователя страница 67

Страница: 67 / 269

Figure 4-23 Connecting communications cables

If the length of a network cable in the FE teamwork is greater than or equal to

100 m, use the group-based ring networking mode.

1. Connecting units with odd numbers: Connect the FE_1 port of the unit with

an odd number to the FE_2 port of the unit with the next odd number.

2. Connecting units with even numbers: Connect the FE_2 port of the unit with

an even number to the FE_1 port of the next unit with an even number.

3. Connect FE_2 of No. 1 unit and FE_1 of No. 2 unit, and connect the remaining

FE_1 and FE_2 of the last two units.

Figure 4-24 FE teamwork group-based ring networking (using 13 units as an

example)

----End

4.5.4.5 FE Te FE Monitoring

First Connection

Step 1 Connect teamwork and monitoring communications cables.

Networking

FE Teamwork

FE Monitoring

Protocol

MAC_CAN

Modbus-TCP/SNMP

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды