Huawei FusionCol8000-E24 Скачать руководство пользователя страница 11

Страница: 11 / 269

●

Damage caused during transportation by the customer

●

Storage conditions that do not meet the requirements specified in this

document

General Requirements

●

Do not install, use, or operate outdoor equipment and cables (including but

not limited to moving equipment, operating equipment and cables, inserting

connectors to or removing connectors from signal ports connected to outdoor

facilities, working at heights, and performing outdoor installation) in harsh

weather conditions such as lightning, rain, snow, and level 6 or stronger wind.

●

Before installing, operating, or maintaining the equipment, remove any

conductive objects such as watches or metal jewelry like bracelets, bangles,

and rings to avoid electric shock.

●

When installing, operating, or maintaining the equipment, wear dedicated

protective gears such as insulation gloves, goggles, and safety clothing,

helmet, and shoes, as shown in the following figure.

●

Follow the specified procedures for installation, operation, and maintenance.

●

Before handling a conductor surface or terminal, measure the contact point

voltage and ensure that there is no risk of electric shock.

●

After installing the equipment, remove idle packing materials such as cartons,

foam, plastics, and cable ties from the equipment area.

●

In the case of a fire, immediately leave the building or the equipment area

and activate the fire alarm or call emergency services. Do not re-enter the

building or affected area until it has been deemed safe by qualified

professionals.

●

Do not stop using protective devices. Pay attention to the warnings, cautions,

and related precautionary measures in this document and on the equipment.

Promptly replace warning labels that have worn out.

●

Keep irrelevant people away from the equipment. Only operators are allowed

to access the equipment.

●

Use insulated tools or tools with insulated handles, as shown in the following

figure.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

1 Safety Information

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды