Huawei FusionCol8000-E24 Скачать руководство пользователя страница 69

Страница: 69 / 269

Figure 4-27 FE teamwork group-based ring networking (using 13 units as an

example)

----End

Scenario Switching

Scenario

Operation

Switching from

the independent

wiring scenario to

the shared wiring

scenario

1. Retain the cable connection to the COM/FE port on a

unit, and disconnect the cables from the COM/FE ports

on other units.

NOTICE

Only the cable connection to the COM/FE port on one unit can

be retained. Otherwise, the communication will fail.

2. Set Monitor FE wiring mode to Shared wiring on the

Access Control screen of each unit.

Switching from

the shared wiring

scenario to the

independent

wiring scenario

1. Set Monitor FE wiring mode to Independent wiring on

the Access Control screen of each unit.

2. Connect the COM/FE port on the main control module

of each unit to the FE port on the host.

4.5.5 Installing Power Cables

Procedure

Step 1 Route power cables through the external cable holes.
Step 2 Open the electric control box outside the unit.
Step 3 Connect one end of the active and standby power cables to the active/standby

power supply terminals/PE terminal through the cable holes in the electric control

box of the unit, and connect the other end to the power supply.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды