Huawei FusionCol8000-E24 Скачать руководство пользователя страница 133

Страница: 133 / 269

Parameter

Description

Communication address

Enter the communications address of the smart

cooling product as planned. The NMS

communicates with the smart cooling product

using this address, and the communications

addresses of two smart cooling products

connected to the same NMS must be different.

RS485 monitoring grouping

● In non-grouping scenarios, set RS485

monitoring grouping to Enable for each unit.

● In grouping scenarios, set RS485 monitoring

grouping to Enable for the unit with the

COM/FE port connected, and Disable for

other units.

----End

7.4.4.2 Setting Communications Parameters (Modbus-TCP Protocol)

Context

This section applies to the scenario where the unit is connected to the NMS.

Procedure

Step 1 On the home screen, choose Settings > Comm Settings > WAN IP Settings, and

set the IP address, subnet mask, and gateway based on the actual plan.

Figure 7-7 WAN IP Settings

NO TE

The WAN IP address cannot be in the 192.168.245.X, 192.168.246.X, or 192.168.248.X

network segment.

Step 2 On the home screen, choose Settings > Comm Settings > Modbus Settings.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

124

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды