Huawei FusionCol8000-E24 Скачать руководство пользователя страница 155

Страница: 155 / 269

Fault

Type

Possible Cause

Solution

The pressure loss is

different from the

designed value.

Check whether the resistance of the air

supply duct is too large.

Vibration

Imbalance

Check whether the fan blades are

damaged, polluted, or frozen.

Abnormal

noise

Bearing damage or

wear

Replace the bearing.

Fan blade friction/

collision

Clear foreign matters or dirt in the fan if

necessary.

The fan is operating

in the stall zone

(applicable to an

axial fan).

Check whether the airflow is smooth

(intake/exhaust air damper and air filter).

The concentricity of

the air intake ring is

incorrect (applicable

to a centrifugal fan).

Observe the installation precautions.

Electric Hazards

●

Electrical components can only be operated by professional electricians or

persons familiar with electricity, or under the supervision of an electrician.

●

Comply with five electrical safety regulations.

●

Do not operate when the unit is powered on. Even after the unit is powered

off, the intermediate circuit is still energized. Wait at least 3 minutes.

●

To disconnect electrical connections safely, take other measures if necessary.

●

For all operations on energized parts or circuits, there must always be two

persons present, so that one person can cut off the power supply in the case

of emergency.

●

The ventilation unit can only be connected to a circuit with an omnipolar

isolation switch.

●

Follow the local standards for electromagnetic compatibility of the unit.

●

Periodically check the electrical devices. Tighten the loose connector and

replace the damaged conductor or cable immediately.

Air Filter

●

When the final resistance of the air filter reaches the specified value, clean or

replace the air filter. Air filters are wear parts.

●

Exercise caution when removing a dusty air filter from the metal frame to

avoid polluting the smart cooling product and damaging the filtering

materials.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

10 Troubleshooting

146

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды