Huawei FusionCol8000-E24 Скачать руководство пользователя страница 127

Страница: 127 / 269

Parameter

Description

Enable teamwork CAN

resistor

If CAN network is selected, set Enable teamwork

CAN resistor to Yes for the first and last units. If

Enable teamwork CAN resistor is set to No for the

first and last units, the CAN communication quality

will be affected, and even the teamwork CAN

networking will fail.
Yes: The teamwork control CAN resistor is enabled

for the unit.
No: The teamwork control CAN resistor is disabled

for the unit.

Teamwork function

Specifies the planned teamwork group number. This

parameter should be the same for all units in the

same teamwork group.

Teamwork parameter

synchronization

If Teamwork function and Teamwork parameter

synchronization are both set to Enable, you can

select Set Local or Set Teamwork when setting

parameters.

NOTE

● Set Local: Set parameters for the local unit.
● Set Teamwork: Set parameters for all units in a

teamwork group.

Number of systems in

this group

Specifies the total number of units in this group. The

value is an integer ranging from 1 to 32.

Number of running

systems in this group

Specifies the number of running units in this group.

The value is an integer ranging from 1 to the value

of Number of systems in this group.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

118

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды