HP Integrity BL890c - i2 Server Скачать руководство пользователя страница 80

Страница: 80 / 229

Scenario 1:6 – VLAN Tagging (802.1Q) with Multiple Shared Uplink Sets (SUS) and Link Aggregation using LACP (802.3ad) –

VMware ESX 80

Figure 1-70

Define Shared Uplink Set (VLAN-Trunk-2).

Note: The Port Status and Connected to information. If the connected switch supports LLDP, the connected to
information should be displayed as below.

Note: Smart Link is enabled, if ALL uplinks to this SUS fail, then server downlinks will be turned off, initiating a NIC

teaming fail-over.

Содержание Integrity BL890c - i2 Server






































































































































































































































Результаты поиска

Содержание Integrity BL890c - i2 Server

Отзывы:

Похожие инструкции для Integrity BL890c - i2 Server

Бренды по названию

Популярные бренды

HP Integrity BL890c - i2 Server, Руководство пользователя

Результаты поиска

Содержание Integrity BL890c - i2 Server

Отзывы:

Похожие инструкции для Integrity BL890c - i2 Server

Бренды по названию

Популярные бренды