HP Integrity BL890c - i2 Server Скачать руководство пользователя страница 201

Страница: 201 / 229

Scenario 3:2 - Flex-10 with Multi-Enclosure stacking - VLAN Tagging (802.1Q) with Multiple Shared Uplink Sets (SUS) - VMware

ESX - (4 Enclosures) 201

VMWARE ESX Host Networking configuration Example

When configuring the ESX virtual switch, add virtual networks for each VLAN this ESX host will support.

Figure 3-33

Configuring the ESX vSwitch for Multiple Networks / VLANs.

Note:

That vSwitch 3 has two NICs configured to, redundantly, support VLANs 103, 104 and 105.

Note:

If implementing ESX 3.5 on Flex-10, first review VMWARE KB 1007982 and ensure Network

Failure Detection is set to Beacon Probing.

Note:

If implementing ESX 4.0 on Flex-10 ensure that ESX driver version 1.52 is installed, also ensure

that NIC firmware 5.2.7 is also installed.

When configuring the guest NIC simply chose which VLAN this guest will reside on.

Содержание Integrity BL890c - i2 Server






































































































































































































































Результаты поиска

Содержание Integrity BL890c - i2 Server

Отзывы:

Похожие инструкции для Integrity BL890c - i2 Server

Бренды по названию

Популярные бренды

HP Integrity BL890c - i2 Server, Руководство пользователя

Результаты поиска

Содержание Integrity BL890c - i2 Server

Отзывы:

Похожие инструкции для Integrity BL890c - i2 Server

Бренды по названию

Популярные бренды