HP Integrity BL890c - i2 Server Скачать руководство пользователя страница 215

Страница: 215 / 229

Appendix B: Scenario-based ProCurve command line reference 215

Simple vNet with Active/Standby Uplinks and Link Aggregation 802.3ad
(LACP)

Connect to the ProCurve switch servicing the VC-Enet uplink ports and enter the following commands.

NOTE: If tw o sw itches are being u sed, issu e the sam e com m ands on the second sw itch.

Table 1b

Scenario 1-1 and 1-2 (Part 2) - ProCurve command line configuration (simple network)

Command

Shortcut

Description

>enable

>en

Privilege mode

#configure terminal

#conf

Configure in global mode

#span

Enables spanning-tree (MSTP mode

by default)

#trunk 1-2 trk1 lacp

Configure LACP port-trunk 1 to

include Ports 1 & 2

#vlan 1 untagged [Ethernet] trk1

#vlan 1 untag trk1

Allow VLAN 1 on Port 1 & 2 , and
set to untagged mode

#spanning-tree ethernet trk1 admin-
edge-port

#span e trk1 admin-edge

Set Port 1 to be an edge port (non
bridging port). Note: port is set by

default in “auto-edge” mode which
automatically sets port to Edge if no
BPDU are received after 3 sec.

#show vlan ports trk1 detail

# show vlan ports trk1 detail

Displays the VLAN detail for Trunk1

#show vlan 1

#sh vlan 1

Display VLAN 1 port information

#write memory

(For permanent changes only)

#write mem

Save the running configuration to
NVRAM. Otherwise, the changes

will be lost on the next reboot.

Содержание Integrity BL890c - i2 Server






































































































































































































































Результаты поиска

Содержание Integrity BL890c - i2 Server

Отзывы:

Похожие инструкции для Integrity BL890c - i2 Server

Бренды по названию

Популярные бренды

HP Integrity BL890c - i2 Server, Руководство пользователя

Результаты поиска

Содержание Integrity BL890c - i2 Server

Отзывы:

Похожие инструкции для Integrity BL890c - i2 Server

Бренды по названию

Популярные бренды