HP Integrity BL890c - i2 Server Скачать руководство пользователя

Страница: 203 / 229

Appendix A: Scenario-based Cisco command line reference 203

Appendix A: Scenario-based Cisco command
line reference

All of the following commands in this appendix assume an unaltered factory default configuration before

execution of the switch commands.

Scenario 1-1 & 1-2 – Cisco IOS command line

configuration (Simple vNet with Active/Standby Uplinks)

Connect to the Cisco switch servicing the VC-Enet uplink ports and enter the following IOS commands.

NOTE: If tw o sw itches are being u sed, issu e the sam e com m ands on the second sw itch.

Table 1a

Scenario 1 (Part 1) - Cisco IOS command line configuration

Command

Shortcut

Description

>enable

>en

Privilege mode

#configure terminal

#config t

Configure via terminal

#interface gigabitethernet0/1

#int gi1/0/1

Focus on Port 1

#switchport mode access

#sw mo ac

Set port 1 for Single VLAN mode

#switchport access vlan 1

#sw ac vl 1

Allow Port 1 access to VLAN 1

#spanning-tree portfast trunk
# this is an access port, is this

required?

#sp portf tr

Enable portfast on Port 1

#exit

Remove focus from Port 1

#exit

Remove focus from Port 1

#show vlan brief

#sh vl br

Display all VLANs

#show interface gigabitethernet0/1
status

#sh int gi0/1 status

Display the status of Port 1

#copy running-config startup-config
(For permanent changes only)

#cop ru st

Save the running configuration to
NVRAM. Otherwise, the changes

will be lost on the next reboot.

Содержание Integrity BL890c - i2 Server






































































































































































































































Результаты поиска

Содержание Integrity BL890c - i2 Server

Отзывы:

Похожие инструкции для Integrity BL890c - i2 Server

Бренды по названию

Популярные бренды

HP Integrity BL890c - i2 Server, Руководство пользователя

Результаты поиска

Содержание Integrity BL890c - i2 Server

Отзывы:

Похожие инструкции для Integrity BL890c - i2 Server

Бренды по названию

Популярные бренды