HP BCDVideo BCD108 Скачать руководство пользователя страница 39

Страница: 39 / 162

Hardware options installation 39

13.

Remove the fan blanks from locations 1 and 2. For fan location and numbering information, see
"Hot-plug fans (on page

)" or the label attached to the chassis next to the fans.

14.

Install the fans into locations 1 and 2.

IMPORTANT:

Do not mix standard fans and high-performance fans in the same server.

15.

Install the access panel (on page

16.

Install the server into the rack.

17.

Connect each power cord to the server.

18.

Connect each power cord to the power source.

19.

Press the Power On/Standby button.
The server exits standby mode and applies full power to the system. The system power LED

changes from amber to green.

Содержание BCDVideo BCD108



































































































































































Результаты поиска

Содержание BCDVideo BCD108

Отзывы:

Похожие инструкции для BCDVideo BCD108

Бренды по названию

Популярные бренды

HP BCDVideo BCD108, Руководство пользователя

Результаты поиска

Содержание BCDVideo BCD108

Отзывы:

Похожие инструкции для BCDVideo BCD108

Бренды по названию

Популярные бренды