HP BCDVideo BCD108 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 162

background image

Component identification 19

NVMe SSD components

The NVMe SSD is a PCIe bus device. A device attached to a PCIe bus cannot be removed without
allowing the device and bus to complete and cease the signal/traffic flow.

CAUTION:

Do not remove an NVMe SSD from the drive bay while the Do Not Remove

button LED is flashing. The Do Not Remove button LED flashes to indicate the device is still in
use. Removal of the NVMe SSD before the device has completed and ceased signal/traffic
flow can cause loss of data.

Item

Description

1

Release lever

2

Activity ring

3

Do Not Remove button

4

Power button

Hot-plug fans

CAUTION:

To avoid damage to server components, fan blanks must be installed in fan bays

1 and 2 in a single-processor configuration.

The only two valid fan configurations are listed in the following table.

Configuration

Fan bay 1 Fan bay 2 Fan bay 3

Fan bay 4 Fan bay 5 Fan bay 6

Fan bay 7

1 processor

Fan blank

Fan blank

Fan

Fan

Fan

Fan

Fan

2 processors

Fan

Fan

Fan

Fan

Fan

Fan

Fan

«
...
17
18
19
20
21
...
»

Содержание BCDVideo BCD108



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCDVideo BCD108

Бренд: IBM Страницы: 180

8841 - eServer xSeries 236

Бренд: IBM Страницы: 100

Бренд: TYAN Страницы: 221

totalstorage 200

Бренд: IBM Страницы: 152

Бренд: IBM Страницы: 142

LUXOMAT net ViSTATION

Бренд: B.E.G. Страницы: 4

Бренд: Hologic Страницы: 30

Бренд: Santec Страницы: 40

Бренд: MSI Страницы: 106

Бренд: Yawarra Страницы: 4

SuperServer 2029BT-HNC0R

Бренд: Supermicro Страницы: 148

Бренд: Artesyn Embedded Technology Страницы: 2

Бренд: Lightwave Communications Страницы: 97

IntraPort A00-1869

Бренд: Compatible Systems Страницы: 44

Бренд: pachanko Страницы: 56

Бренд: Intel Страницы: 270

Бренд: TROY Group Страницы: 34

Бренд: TROY Group Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды