hopf 8029NTS-V2/GPS Скачать руководство пользователя | Manualshive

Страница: 85 / 121

background image

HTTP/HTTPS

W

EB

GUI

–

W

EB

B

ROWSER

C

ONFIGURATION

I

NTERFACE

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

85 / 121

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

Current Sync Source Time

This area indicates the curent time and date of the Sync Source. Both the local and UTC time
are displayed.

In theory, depending on the synchronization status of the Sync Source,
the time displayed here can differ from the NTP time since two
independent time systems are involved.

Announcements

The display fields LEAP SECOND and STD



DST announce a corrosponding event to the

next hour (insertion of a leap-second or rather switch-over of summer/winter time).

Sync Source Status

Display of the actual status of synchronization of the Sync Source with these possible values:

SYNC

Time synchr Quartz regulation started/running

SYOF

Time synchr SyncOFF running

SYSI

Time synchronized as simulation mode
(without actual GPS reception)

QUON

Quartz/Crystal time + SyncON running

QUEX

Quartz/Crystal time (in freewheel after synchronization
failure



Board was already synchronized)

QUSE

Quartz/Crystal time after reset or manual setting

INVA

Invalid time

7.3.6.2 Set Sync Source Time

Adjustment of UTC including the date in the Sync Source (here Module 8024GPS)

After entering the plausibility of these values are directly checked by clicking on the

Apply

button and then sent to the Sync Source (here Module 8024GPS).

Always the UTC time must be set. The local time is internally calculated
from the difference time (Time Zone Offset) and the summer / winter time
changeover (Daylight Saving Time).

«
...
83
84
85
86
87
...
»

Содержание 8029NTS-V2/GPS


























































































































Отзывы:

Нет отзывов

Похожие инструкции для 8029NTS-V2/GPS

Бренд: ReelCraft Страницы: 9

PURE RESONATOR SB

Бренд: K&K Sound Страницы: 2

Бренд: ClearOne Страницы: 2

Бренд: Absco Страницы: 22

VELA INDUSTRIAL

Бренд: SEA USA Страницы: 16

NANOPONIC Series

Бренд: Aquatop Страницы: 4

Бренд: General Pump Страницы: 2

Бренд: Browning Страницы: 2

ACTLAN - INTERFACE

Бренд: ACT Страницы: 2

Бренд: Geokon Страницы: 64

Бренд: VIGO Страницы: 18

Бренд: Fishman Страницы: 4

Star Wars Jedi Challenges

Бренд: Lenovo Страницы: 11

Бренд: Lenovo Страницы: 16

Бренд: Racelogic Страницы: 5

Бренд: Eco-lamps Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Tecma Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды