hopf 8029NTS-V2/GPS Скачать руководство пользователя

Страница: 40 / 121

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

40 / 121

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

7.3

Description of the Tabs

The WebGUI is divided into the following tabs:

•

General

•

Network

•

NTP

•

Alarm

•

Device

•

GPS Sync Source

7.3.1 GENERAL Tab

This is the first tab displayed when using the web interface.

NTP Time Status

This area shows basic information about the current time and date of the Time Server
8029NTS/GPS. The time

always

corresponds to UTC. The reason for this is that NTP always

works with UTC and not with local time.

Stratum displays the actual NTP stratum value of the Time Server 8029NTS/GPS with the
value range from 1-16.

The

ACCURACY

field (accuracy of NTP) can contain the values LOW - MEDIUM - HIGH. The

meaning of these values is explained in

Chapter 13.5

Accuracy & NTP Basic Principles

Содержание 8029NTS-V2/GPS


























































































































Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Похожие инструкции для 8029NTS-V2/GPS

Бренды по названию

Популярные бренды

hopf 8029NTS-V2/GPS, Техническое руководство

Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Похожие инструкции для 8029NTS-V2/GPS

Бренды по названию

Популярные бренды