hopf 8029NTS-V2/GPS Скачать руководство пользователя

Страница: 13 / 121

YSTEM

TRUCTURE

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

13 / 121

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

2.3.2 NTP Status LEDs (NTP/Stratum/Accuracy)

NTP-LED (Green)

NTP sewrvice of the Time Server 8029NTS/GPS

Standard

, running

Off

Not running

Stratum1-LED
(Green)

The NTP service of the Time Server 8029NTS/GPS
works with:

Stratum 1

Flashes

Stratum 2-15

Off

Stratum 16 (no synchronization of NTP Clients)

Accuracy-LED
(Green)

The NTP service of the Time Server 8029NTS/GPS
works with accuracy of:

high

Flashes

medium

Off

low

2.3.3 USB-Port

On specific problems the USB connection can be used for a system recovery
after consulting the

hopf

Support.

2.3.4 LAN Interface ETH0

10/100-LED
(Green)

Description

Off

10 MBit Ethernet detected

100 MBit Ethernet detected

lnk/act-LED
(Yellow)

Description

Off

No LAN connection to a network

LAN connection available

Flashes

Network activity at ETH0 (transmission / reception)

Pin No.

Assignment

Tx+

–

Rx+

Not in use

–

Not in use

Содержание 8029NTS-V2/GPS


























































































































Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Похожие инструкции для 8029NTS-V2/GPS

Бренды по названию

Популярные бренды

hopf 8029NTS-V2/GPS, Техническое руководство

Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Похожие инструкции для 8029NTS-V2/GPS

Бренды по названию

Популярные бренды