hopf 8029NTS-V2/GPS Скачать руководство пользователя

Страница: 48 / 121

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

48 / 121

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

7.3.2.2 Routing (Activation Key necessary)

A route must be configured if the module is not only be used in the local sub-network.

The gateway / gateway host need to be in the local sub-network range of the module in order
to use the routes.

The parameterization of this feature is a critical process as an incorrect
configuartion may lead to considerable problems on the network!

WebGUI with Routing activated

The image above shows every configured route of the base system routing table as well as
the user

’s defined routes.

The module cannot be used as a router

Select

Use Route File

to set whether the routing configuration set under

User Defined

Routes

should be used, or routing configuration using a routing file.

If IPv6 routes are required, the routes must be made using the settings in

Chapter 7.3.2.3 Routing File

Содержание 8029NTS-V2/GPS


























































































































Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Похожие инструкции для 8029NTS-V2/GPS

Бренды по названию

Популярные бренды

hopf 8029NTS-V2/GPS, Техническое руководство

Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Похожие инструкции для 8029NTS-V2/GPS

Бренды по названию

Популярные бренды