manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Техническое руководство

Поделиться
Скачать
hopf 8029NTS-V2/GPS Скачать руководство пользователя страница 90

 

HTTP/HTTPS

 

W

EB

GUI

 

–

 

W

EB 

B

ROWSER 

C

ONFIGURATION 

I

NTERFACE

 

 

 

 90 / 121 

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

hopf 

Elektronik GmbH 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

 

7.3.6.8  SyncON / SyncOFF 

 

 

 

SyncON Timer

 

The SyncON timer is used to delay the sync-

status “SYNC” by the set time although the GPS 

receiver is synchronous. 

This function is enabled when adjustment processes should be terminated as defined before 
the sync status is “SYNC”.  

This function is not required for this device and should always be set to 0. 

 

SyncOFF Timer

 

This value is used to provide reception failure bypassing for an error-message free operation 
even under poor reception conditions. 

In  the  event  of  a  reception  failure  of  the  Sync  Soure  (here  Module  8024GPS),  the  re-
synchronization of the Sync Source to 

quartz 

status is delayed by the set value. The system 

continues to run in synchronization status 

'SYOF'

 on the internally regulated, highly accurate 

quartz base during this period. 

This timer is of special significance when certain system outputs are linked to a specific system 
status.  

The Timer can be set from 2min. to 1440min.  

 

Current Timer values

 

In case of an active Timer the appropriate value of the timer is displayed here. 

 

Содержание 8029NTS-V2/GPS


























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды