hopf 8029NTS-V2/GPS Скачать руководство пользователя страница 50

Страница: 50 / 121

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

50 / 121

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

7.3.2.4 Management (Management-Protocols

– HTTP, SNMP etc.)

Protocols that are not required should be disabled for security reasons. A correctly configured
module is always accessible via the web interface.

Changes to the availability of a protocol (enable/disable) take effect immediately.

For SNMP functionality an activation key is necessary.

If by mistake all protocol channels become "disabled", the SSH channel is
automatically "enabled" after the attempt to save.

After a Factory Default the HTTP and SSH channels are "enabled".

These service settings are valid globally

! Services with “disabled” status are

not externally accessible and are not made externally available by the
module!

Содержание 8029NTS-V2/GPS


























































































































Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Бренды по названию

Популярные бренды

hopf 8029NTS-V2/GPS, Техническое руководство

Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Бренды по названию

Популярные бренды