hopf 8029NTS-V2/GPS Скачать руководство пользователя

Страница: 97 / 121

SSH

AND

ELNET

ASIC

ONFIGURATION

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

97 / 121

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

SSH and Telnet Basic Configuration

Only basic configuration is possible via SSH or Telnet. The complete
configuration of the Time Server 8029NTS/GPS takes place exclusively
via the WebGUI.

It is just as easy to use SSH (Port 22) or Telnet (Port 23) as the WebGUI. Both protocols use
the same user interface and menu structure.

The user names and passwords are the same as on the WebGUI and are kept in alignment
(see

Chapter 7.3.5.5 Passwords (Master/Device)

SSH does not allow blank passwords for safety reasons.

The corresponding protocols should be enabled for the use of Telnet or
SSH (see

Chapter 7.3.2.4 Management (Management-Protocols

–

HTTP, SNMP etc.)

The navigation through the menu takes place by entering the respective number associated
with the menu option (as can be seen in the above image).

Содержание 8029NTS-V2/GPS


























































































































Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Похожие инструкции для 8029NTS-V2/GPS

Бренды по названию

Популярные бренды

hopf 8029NTS-V2/GPS, Техническое руководство

Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Похожие инструкции для 8029NTS-V2/GPS

Бренды по названию

Популярные бренды