hopf 8029NTS-V2/GPS Скачать руководство пользователя | Manualshive

Страница: 45 / 121

background image

HTTP/HTTPS

W

EB

GUI

–

W

EB

B

ROWSER

C

ONFIGURATION

I

NTERFACE

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

45 / 121

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

7.3.2.1.9 Customer Hardware Address (MAC)

The MAC address assigned from

hopf

can be changed to any user-defined MAC address.

The board identifies itself with the user-defined MAC address to the network. The default
hardware address shown in WebGUI remains unchanged.

Double assignment of MAC addresses on the Ethernet referring to
customers MAC addresses should be avoided.
If the MAC address is not known, please contact your network
administrator.

The use of customers MAC address needs to be activated by the function

Use Custom

Hardware Address (MAC

) with

enable

.

The customers MAC address has to be entered in hexadecimal form with a colon to separateas
described in the below example, e.g.

00:03:c7:55:55:02

The MAC address assigned by

hopf

can be activated at any time by

disabling this function.

There are no MAC multicast addresses allowed!

7.3.2.1.10 DHCP

If DHCP is to be used, activate this with

enabled

.

7.3.2.1.11 IPv4 Address

If DHCP is not used, the IPv4 address needed to be entered here. Contact your network
administrator for details of the used IPv4 address if not known.

7.3.2.1.12 IPv4 Network Mask

If DHCP is not used, the network mask needed to be entered here. Contact your network
administrator for details of the used network mask if not known.

«
...
43
44
45
46
47
...
»

Содержание 8029NTS-V2/GPS


























































































































Отзывы:

Нет отзывов

Похожие инструкции для 8029NTS-V2/GPS

Digitrip RMS 310

Бренд: Eaton Страницы: 20

Бренд: SEH Страницы: 20

Бренд: Gibson Страницы: 2

Бренд: WEG Страницы: 2

Бренд: Aqua Medic Страницы: 20

Бренд: Woodward Страницы: 22

Бренд: SeeedStudio Страницы: 11

ENTERPRISE LINUX

Бренд: Red Hat Страницы: 104

Бренд: Audio Technica Страницы: 22

Бренд: Aqua Medic Страницы: 18

Boxer D44C QUATTRO Combi

Бренд: Drester Страницы: 17

Бренд: Yiimix Страницы: 9

Бренд: Quest Engineering Страницы: 14

Бренд: SENDO Страницы: 6

Бренд: Calix Страницы: 6

Бренд: Digital-Ally Страницы: 17

Бренд: Endace Страницы: 22

Бренд: Christie Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды