hopf 8029NTS-V2/GPS Скачать руководство пользователя страница 22

Страница: 22 / 121

NSTALLATION

22 / 121

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

Installation

The installation of the Time Server 8029NTS/GPS is described below.

5.1

Installation/Dismounting of the DIN Rail Housing

The Time Server 8029NTS/GPS can be mounted on all rails in accordance with DIN EN 60715
TH35 and is designed for horizontal mounting.

Dimensions

The dimensions of the housing can be found in

Chapter 11.5 Dimensions

– DIN Rail

Housing.

•

Time Server 8029NNTS/GPS

–

Housing: TYPE 2

In order to guarantee an adequate convection, we recommend the
following minimum distance from other modules:

•

5.0 cm in vertical direction and

•

1.0 cm in horizontal direction.

5.1.1 Mounting

Place

the module’s rail guide bar against the lower edge of the rail, push the module

upwards, and clip to the back.

5.1.2 Dismounting

Push the module upwards and then tip forward to remove from the rail.

Содержание 8029NTS-V2/GPS


























































































































Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Бренды по названию

Популярные бренды

hopf 8029NTS-V2/GPS, Техническое руководство

Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Бренды по названию

Популярные бренды