hopf 8029NTS-V2/GPS Скачать руководство пользователя | Manualshive

Страница: 16 / 121

background image

F

UNCTION

P

RINCIPLE

16 / 121

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

3

Function Principle

This chapter describes the function principle of the Time Server 8029NTS/GPS and the
internal relations between the different functional groups.

3.1

Block Diagram

•

Internal Supply Voltage

The individual functional components are supplied with the required operating voltage
via the implemented power supply unit.

•

Firmware Update

A H8 firmware update of the Sync Souce (here Module 8024GPS) is completey
controlled by Module 8029NTS.
The update file for Module 8024GPS is loaded into Module 8029NTS via LAN through
the WebGUI. Then Module 8029NTS performs the update of the Sync Source (here
Module 8024GPS) independently.

•

Management

The entire control of the Sync Source (here Module 8024GPS) is done by Module
8029NTS. All data of the Sync Source, indicated via WebGUI, are demanded cyclically
by Module 8029NTS from the Sync Source (here Module 8024GPS) or if necessary.
These data are then prepared for the display in WebGUI. After activation settings for
the Sync Source are transferred to the Sync Source immediately.

•

High Precision Time

The Sync Source provides a high-precision time information and the according
synchronization status to Module 8029NTS. This time and status information is used
for synchronization of the NTP service and if applicable other signal generations
running on 8029NTS.

«
...
14
15
16
17
18
...
»

Содержание 8029NTS-V2/GPS


























































































































Отзывы:

Нет отзывов

Похожие инструкции для 8029NTS-V2/GPS

SCH-U430 Series

Бренд: Samsung Страницы: 2

Бренд: Parkside Страницы: 30

Radial 40 Rewind

Бренд: Harken Страницы: 27

Бренд: Flymo Страницы: 80

COOLIUS 4000 HP

Бренд: Wow Страницы: 32

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 4

NETWORK CHANGE PLAN REVIEW - SERVICE DESCRIPTION DOCUMENT 10-2010

Бренд: Juniper Страницы: 4

Бренд: Snap-On Страницы: 14

Бренд: Dwyer Instruments Страницы: 2

Бренд: Ideal Air Страницы: 8

Бренд: GE Multilin Страницы: 254

Бренд: V2 Страницы: 32

NAVIGATOR - OPERATING GUIDE ADDENDUM

Бренд: SABINE Страницы: 2

Бренд: Airaid Страницы: 2

Бренд: Fabtech Страницы: 10

Бренд: Magnetic Autocontrol Страницы: 81

CHELSEA 267 Series

Бренд: Parker Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды