background image

 

www.fabtechmotorsports.com

 

4331 EUCALYPTUS AVE. CHINO, CA. 91710 

PHONE 909-597-7800   FAX 909-597-7185 

 
 

2007 - 13 GM 1500 4WD – 2WD SUV REAR SYSTEM 

  

 

FTS21051BK REAR AUTO RIDE COIL SPRING SYSTEM   

 

FTS21052BK REAR Non /AUTO RIDE COIL SPRING SYSTEM   

 

 
 

THIS INSTRUCTION SHEET COVERS THE INSTALLATION OF VEHICLES WITH AND WITHOUT AUTO RIDE 

SUSPENSION. VERIFY THAT YOU HAVE THE CORRECT KIT FOR YOUR APPLICATION. 

 

READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION! 

 

CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST ABOVE BEFORE BEGINNING 

INSTALLATION OF THE KIT. IF ANY PIECES ARE MISSING, CONTACT FABTECH AT 909-597-7800 

 

VEHICLES THAT WILL RECEIVE OVERSIZED TIRES SHOULD CHECK BALL JOINTS, TIE RODS ENDS AND 

IDLER ARM EVERY 2500-5000 MILES FOR WEAR AND REPLACE AS NEEDED. 

 

WARNING: 

FABTECH RECOMMENDS THAT YOU EXERCISE EXTREME CAUTION WHEN WORKING 

WITH COIL SPRINGS TO AVOID ANY POSSIBILITY OF INJURY. 

 
                                       THIS KIT NOT RECOMMEND FOR 2WD SUBURBAN. 
 
  
TOOL LIST:     (NOT INCLUDED) 

o

 

FLOOR JACK 

o

 

JACK STANDS 

o

 

EXTERNAL COIL SPRING COMPRESSOR 

o

 

ASSORTED METRIC AND S.A.E SOCKETS, & ALLEN WRENCHES  

       

o

 

DRILL WITH 7/16” BIT 

o

 

DIE GRINDER WITH CUT OFF WHEEL 

 
 

Summary of Contents for FTS21051BK











Reviews: