VIGO VG06031 Installation Manual Download

Page: 1 / 18

This Installation Guide uses the following symbols to indicate important information.
Always observe the instructions indicated by these symbols.

VIGO INDUSTRIES INSTALLATION GUIDE FOR

SHOWER ENCLOSURE (MODEL VG06031)

Instructions that, if ignored, could result in death or serious personal injury caused by
incorrect handling or installation of the product. These instructions must be observed for

safe installation.

Maintenance and other important non-personal injury and non-material damage instructions

or statements that should be observed.

It is highly advised to dry fit the unit prior to any installation.

IMPORTANT

SAFETY PRECAUTIONS

WARNING

The instructions for the following unit is based off of the Vigo brand shower base. The

instructions can not be provided for any other installation other than that of the Vigo brand.

The warranty will be voided if the following was not performed properly.

CAUTION

Summary of Contents for VG06031



















Search results

Summary of Contents for VG06031

Reviews:

Related manuals for VG06031

Brands by name

Popular brands

VIGO VG06031, Installation Manual

Search results

Summary of Contents for VG06031

Reviews:

Related manuals for VG06031

Brands by name

Popular brands