Honda CBF600N Скачать руководство пользователя страница 617

Страница: 617 / 620

TROUBLESHOOTING

23-6

POOR PERFORMANCE AT HIGH SPEED

1. Ignition Timing Inspection

Check the ignition timing.

Is the ignition timing as specified?

YES

–

GO TO STEP 2.

–

• Faulty ECM
• Faulty CKP sensor
• Faulty VS sensor
• Improper valve timing

2. Fuel Pump Inspection

Inspect the fuel flow.

Is the fuel pump unit operation normal?

YES

–

GO TO STEP 3.

–

Faulty fuel pump unit (page 5-56).

3. PGM-FI System Inspection

Check the PGM-FI system.

Is the PGM-FI system normally?

YES

–

GO TO STEP 4.

–

Faulty PGM-FI system (page 5-11).

4. Valve Timing Inspection

Check the valve timing (page 8-28).

Is the valve timing correct?

YES

–

GO TO STEP 5.

–

Camshafts not installed properly

5. Valve Spring Inspection

Check the valve springs.

Is the valve spring free length as specified?

YES

–

Not weak

–

Faulty valve springs

POOR HANDLING

Steering is heavy

• Steering stem adjusting nut too tight
• Damaged steering head bearings
• Insufficient tire pressure

Either wheel is wobbling

• Excessive wheel bearing play
• Bent rim
• Swingarm pivot bearing excessively worn
• Bent frame

The motorcycle pulls to one side

• Front and rear wheel not aligned
• Faulty shock absorber
• Bent fork
• Bent swingarm
• Bent axle
• Bent frame

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CBF600N

Отзывы:

Honda CBF600N, Руководство по обслуживанию, Страница: 617 / 620

Результаты поиска

Содержание CBF600N

Отзывы: