Honda CBF600N Скачать руководство пользователя страница 281

Страница: 281 / 620

CYLINDER HEAD/VALVES

8-23

The exhaust valve

springs has a green

paint marks and the

intake valve springs

has gray paint

marks.

Install the valve springs with the tightly wound coils
facing the combustion chamber.

Install the valve spring retainer.

Grease the cotters

to ease installation.

Install the valve cotters using the special tool as
shown.

To prevent loss of tension, do not compress the
valve spring more than necessary.

Support the

cylinder head above

the work bench

surface to prevent

possible valve

damage.

Tap the valve stems gently with plastic hammer and
pin driver as shown to seat the cotters firmly.

Install and tighten the spark plugs.

Apply a locking agent to the bleeding joint threads.

Install the bleeding joint with a new sealing washer
to the cylinder head.

Tighten the bleeding joint to the specified torque.

EXHAUST VALVE
SPRING

INTAKE VALVE
SPRING

COMBUSTION CHAMBER SIDE

TOOLS:
Valve spring compressor

07757-0010000

Valve spring compressor
attachment

07959-KM30101

VALVE SPRING COMPRESSOR

ATTACHMENT

TORQUE: 16 N·m (1.6 kgf·m, 12 lbf·ft)

PLASTIC HAMMER

PIN DRIVER

TORQUE: 12 N·m (1.2 kgf·m, 9 lbf·ft)

BLEEDING JOINT

SEALING WASHER

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CBF600N

Отзывы:

Honda CBF600N, Руководство по обслуживанию, Страница: 281 / 620

Результаты поиска

Содержание CBF600N

Отзывы: