Honda CBF600N Скачать руководство пользователя страница 496 | Manualshive

Страница: 496 / 620

Honda CBF600N Скачать руководство пользователя страница 496

ANTI–LOCK BRAKE SYSTEM (ABS; CBF600SA/NA)

16-14

3. Speed Sensor Line Short Circuit Inspection (at

control unit side)

Remove the following:

– seat (page 2-4)
– right side cover (page 2-5)

Disconnect the ABS modulator 25P connector
and the speed sensor 2P (Green) connector.
Check for continuity between the Pink/white wire
terminal of the connector and ground, and
between the Green/red wire terminal of the con-
nector and ground.

Is there continuity?

YES

–

Short circuit in wire between the ABS
modulator and speed sensor.

NO

–

GO TO STEP 4.

4. Speed Sensor Line Short Circuit Inspection (at

sensor side)

Check for continuity between each terminal
(Black and White) of the sensor side 2P (Red)
connector and ground in the same manner as
the previous step.

Is there continuity?

YES

–

Faulty rear wheel speed sensor.

NO

–

GO TO STEP 5.

5. Speed Sensor Line Open Circuit Inspection

Short the Pink/white and Green/red wire termi-
nals of the 25P connector with a jumper wire.
Check for continuity between the terminals of
the wire harness side sensor 2P (Red) connector.

Is there continuity?

YES

–

GO TO STEP 6.

NO

–

Open circuit in wire between the ABS
modulator and speed sensor.

TOOL:
Test probe

07ZAJ-RDJA110

CONNECTION: Pink/white – Ground

Green/red – Ground

Pink/white

Green/red

MODULATOR 25P CONNECTOR
(Wire side/female terminals)

CONNECTION: Black – Ground

White – Ground

2P (Red) CONNECTOR
(Sensor side/male terminals)

Black

White

CONNECTION: Black – White

Pink/white

Green/red

2P (Red) CONNECTOR
(Wire side/male terminals)

MODULATOR 25P CONNECTOR
(Wire side/male terminals)

White

Black

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
494
495
496
497
498
...
»

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов