Honda CBF600N Скачать руководство пользователя страница 295

Страница: 295 / 620

CLUTCH/STARTER CLUTCH/GEARSHIFT LINKAGE

9-5

RIGHT CRANKCASE COVER REMOVAL

Drain the engine oil (page 3-15).

Remove the bolt and clutch cable guide plate, then
disconnect the clutch cable end from the clutch lifter
lever.

Release the EOP switch wire from the clamp.

Remove the right crankcase cover bolts and clamp.

The lifter lever

spindle is engaged

with the clutch lifter

piece inside of the

right crankcase

cover.

Remove the right crankcase cover while turning the
clutch lifter lever counterclockwise to disengage the
lifter lever spindle from the lifter piece.

Be careful not to drop the thrust/wave washers into
the crankcase when removing the right crankcase
cover.

Remove the thrust washer and wave washer from
the starter idle gear.

GUIDE PLATE

LIFTER LEVER

CLUTCH CABLE

BOLT

RIGHT CRANKCASE COVER

BOLTS

CLAMP

LIFTER LEVER

WAVE WASHER

THRUST WASHER

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CBF600N

Отзывы:

Honda CBF600N, Руководство по обслуживанию, Страница: 295 / 620

Результаты поиска

Содержание CBF600N

Отзывы: