Honda CBF600N Скачать руководство пользователя страница 528 | Manualshive

Страница: 528 / 620

Honda CBF600N Скачать руководство пользователя страница 528

IGNITION SYSTEM

18-6

Avoid touching the

spark plugs and

tester probes to

prevent electric

shock.

Turn the ignition switch ON and engine stop switch
"

".

Check for initial voltage at this time.
The battery voltage should be measured.
If the initial voltage cannot be measured, check the
power supply circuit (refer to the troubleshooting,
page 18-4).

Shift the transmission into neutral.
Crank the engine with the starter motor and read
ignition coil primary peak voltage.

If the peak voltage is abnormal, refer to the trouble-
shooting chart (page 18-4).

CKP SENSOR PEAK VOLTAGE

• Check all system connection before inspection. If

the system is disconnected, incorrect peak volt-
age might be measured.

• Check cylinder compression and check that the

spark plugs are installed correctly.

Disconnect the ECM 33P (Black and Light gray) con-
nectors from the ECM (page 5-97).

Connect the peak voltage tester or peak voltage
adaptor probes to the ECM connector terminals of
the wire harness side.

Crank the engine with the starter motor and read
the peak voltage.

If the peak voltage measured at ECM 33P connec-
tors is abnormal, measure the peak voltage at the
CKP sensor connector.

Disconnect the CKP sensor 2P (Red) connector and
connect the tester probes to the terminal (Yellow
and White/yellow).
In the same manner as at the ECM connectors, mea-
sure the peak voltage and compare it to the voltage
measured at the ECM connectors.

• If the peak voltage measured at the ECM is

abnormal and the one measured at the CKP sen-
sor is normal, the wire harness has an open cir-
cuit or loose connection.

• If both peak voltage measured are abnormal,

check each item in the troubleshooting chart
(page 18-4).
If all items are normal, the CKP sensor is faulty.
See following steps for CKP sensor replacement.

PEAK VOLTAGE: 100V minimum

TOOLS:
Imrie diagnostic tester (model 625) or
Peak voltage adaptor

07HGJ-0020100

with commercially available digital multimeter
(impedance 10 M

Ω

/DCV minimum)

Test probe

07ZAJ-RDJA110

CONNECTION:

Yellow (+) – White/yellow (–)

PEAK VOLTAGE: 0.7 V minimum

33P (Light gray) CONNECTOR
(Wire side/female terminals)

33P (Black) CONNECTOR
(Wire side/female terminals)

White/yellow

PEAK VOLTAGE ADAPTOR

Yellow

2P (Red) CONNECTOR

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
526
527
528
529
530
...
»

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов