Honda CBF600N Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 620

Honda CBF600N Скачать руководство пользователя страница 133

FUEL SYSTEM (PGM-FI)

5-19

2. MAP Sensor System Inspection 2

Turn the ignition switch OFF.

Disconnect the MAP sensor 3P (Black) connec-
tor.
Connect the MAP sensor terminals at the wire
harness side with a jumper wire.

Turn the ignition switch ON and engine stop
switch "

".

Check the MAP sensor with the HDS pocket
tester.

Is about 0 V indicated?

YES

–

Faulty MAP sensor

NO

–

GO TO STEP 3.

3. MAP Sensor Input Voltage Inspection

Turn the ignition switch OFF.
Remove the jumper wire.

Turn the ignition switch ON and engine stop
switch "

".

Measure the voltage at the wire harness side.

Is the voltage within 4.75 – 5.25 V?

YES

–

GO TO STEP 4.

NO

–

• Open circuit in Yellow/red wire
• Open circuit in Green/orange wire

4. MAP Sensor Output Line Open Circuit Inspec-

tion

Disconnect the ECM 33P (Light gray) connector.
Check for continuity at the Light green/yellow
wire between the MAP sensor 3P (Black) connec-
tor terminal and the ECM 33P (Light gray) con-
nector.

Is there continuity?

YES

–

Replace the ECM with a known good
one, and recheck; refer to Key Registra-
tion Procedures (page 21-6)

NO

–

Open circuit in Light green/yellow wire

CONNECTION: Light green/yellow – Green/

orange

Green/orange

JUMPER WIRE

3P (Black) CONNECTOR
(Wire side/female terminals)

Light green/yellow

CONNECTION: Yellow/red (+) – Green/orange (–)

3P (Black) CONNECTOR
(Wire side/female terminals)

Green/
orange

Yellow/
red

CONNECTION: B9 – Light green/yellow

TOOL:
Test probe

07ZAJ-RDJA110

33P (Light gray) CONNECTOR
(Wire side/female terminals)

3P (Black) CONNECTOR
(Wire side/female terminals)

B9
TERMINAL

Light green/
yellow

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
131
132
133
134
135
...
»

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов