Honda CBF600N Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 620

Honda CBF600N Скачать руководство пользователя страница 168

FUEL SYSTEM (PGM-FI)

5-54

FUEL PRESSURE TEST

Relieve the fuel pressure and disconnect the quick
connect fitting (page 5-51).

Attach the fuel pressure gauge, attachments and
manifold.

Temporally connect the battery negative (–) cable to
the battery.
Connect the fuel pump 2P (Black) connector.
Start the engine and let it idle.
Read the fuel pressure.

If the fuel pressure is higher than specified, replace
the fuel pump assembly (faulty fuel pump or fuel
pressure regulator).
If the fuel pressure is lower than specified, inspect
the following:

– fuel line leaking
– pinched or clogged fuel feed hose or fuel tank

breather hose

– fuel pump (page 5-56)
– clogged fuel filter (Assembly of the fuel pump:

page 5-56)

Wrap a shop towel

around the

attachment to soak

up any spilled fuel.

After inspection, relieve the fuel pressure by discon-
necting the quick connect fitting (page 5-51).

Remove the fuel pressure gauge, attachment, joint
and manifold from the fuel pump.

Connect the quick connect fitting (page 5-52).

TOOLS:
(1): Fuel pressure gauge

07406-0040004

(2): Pressure gauge manifold

07ZAJ-S5A0111

(3): Pressure gauge hose attach-

ment A

07ZAJ-S5A0120

(4): Pressure gauge hose attach-

ment C

07ZAJ-S7C0100

(5): Fuel attachment joint C

07ZAJ-S7C0200

STANDARD: 343 kPa (3.5 kgf/cm

2

, 50 psi)

(1)

(2)

(3)

(4)

(5)

QUICK CONNECT FITTING

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
166
167
168
169
170
...
»

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов