Honda CBF600N Скачать руководство пользователя страница 169

Страница: 169 / 620

FUEL SYSTEM (PGM-FI)

5-55

FUEL FLOW INSPECTION

Remove the rear cowl (page 2-5).

Remove the fuel cut-off relay from the rubber
holder.

Disconnect the fuel cut-off relay connector.

Jump the Brown and Black/white wire terminals of
the wire harness side using a jumper wire.

• Place an approved gasoline container and drain

the gasoline.

• Wipe off spilled out gasoline.

Disconnect the quick connect fitting from the fuel
joint (page 5-51).
Attach the hose attachment to the fuel joint.

Turn the ignition switch ON for 10 seconds.
Measure the amount of fuel flow.

If the fuel flow is less than specified, inspect the
following:
– pinched or clogged fuel hose
– fuel pump unit (page 5-56)

Remove the hose attachment from the fuel joint and
connect the quick connect fitting (page 5-52).

FUEL CUT-OFF RELAY

CBF600S/SA

CBF600N/NA

FUEL CUT-OFF RELAY

JUMPER WIRE

RELAY TERMINALS

Black/white

Brown

TOOL:
Pressure gauge hose
attachment C

07ZAJ-S7C0100

Amount of fuel flow:

189 cm

(6.4 US oz, 6.7 Imp oz) minimum

/10 seconds at 12 V

ATTACHMENT

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CBF600N

Отзывы:

Honda CBF600N, Руководство по обслуживанию, Страница: 169 / 620

Результаты поиска

Содержание CBF600N

Отзывы: